Weatherby Nation

...  is a smooth bore. Call Wby and I am sure they can help  ...

...  with a barrel than just how smooth the bore is such as concentricity (How centered  ...
...  the bore in the barrel), uniform depth/width of  ...
...  a little yaw when the bullet leaves the bore, opens up the group. Of course this  ...
...  it does not matter if it has a rougher bore than other rifles unless you are a comp  ...

...  got a 'bee and it's got plenty of freebore, and yet it shoots sub-.5" groups at  ...

...  : I have never had much use for any bore sighter. I suppose there OK for blind  ...
...  tree, center the ball looking thru the bore and adjust the scope. Then take it to  ...

...  to be two general weatherby 12 ga. "bore types" or sizes (.730 and .735). I  ...
...  is and help me figure out which "bore type" my shotgun has. Any help here  ...

...  by spreading moly over a contaminated bore surface. The importance of starting out  ...
...  a clean bore. Nobody enjoys it, but a good-old- ...
...  job by selecting a standard, bronze bore brush one caliber oversize, and  ...
...  Bore Cleaner. Be prepared to push a little  ...
... 's 7.62, Hoppe's Benchrest, Butch's Bore Shine, or go with J-B's Non-Embedding  ...
...  Cleaning Compound worked into a bore mop or a patch wrapped around your bore  ...
...  like Barnes CR-10 that can harm the bore when left there too long. If you are  ...
... . When you are comfortable that the bore is free of lead, powder and copper,  ...
... .

How To Treat Your Barrel With Moly Bore Paste:Wrap a cleaning patch around a  ...
...  one bore size smaller than your barrel. Rub a  ...
...  amount of Brownells Moly Bore Treatment Paste into the patch. Warming  ...
...  of the treatment.

Swab the bore with Brownells Moly Bore Treatment  ...
...  twelve to fifteen passes through the bore.) Run a dry patch ten to twelve passes  ...
...  the bore to both remove any excess Moly Bore  ...
...  Paste, and burnish in the Moly Bore Treatment Paste.

Routine Cleaning  ...
... , the time to clean is when the level of bore fouling becomes detrimental to accuracy. ...
...  remove all existing moly residue in the bore and provide a "fresh" bore surface to  ...
...  shooters is Kroil and J-B Non-Embedding Bore Cleaning Compound. Nothing seems to get  ...
...  deep to loosen and lift it from the bore surface. J-B gently removes the  ...
...  a couple patches of Kroil through the bore followed by several dry patches. Resume  ...
...  stoke J-B about ten times through the bore, followed by two patches of Kroil.  ...
...  by pushing dry patches through the bore until they appear clean and dry.

If  ...
... , run a patch of gun oil through the bore to prevent rust and corrosion. Before  ...
... , dry the bore completely and treat a couple of  ...
...  patches or a bore mop with Brownells Moly Bore Treatment  ...
... . Run it down the bore to burnish the moly into the surface  ...

...  tell me if they know of a Bullet Laser Boresighter for the WBY 257 Magnum? ...

...  you're using the stoney point style bore guide, be aware that there are  ...

...  need, one-piece cleaning rod, bore solvent, jag, brush, 100% cotton  ...
... , and lubricant/oil. Bore guide if you have one.

http://www. ...
...  accumulates quickly on an un-lubricated bore and will degrade accuracy.
 ...

...  free bore is there to lower case pressures,  ...

...  false length measure from a custom freebored barrel. I wouldnt think this could  ...

...  somebody says it should have more freebore,then do it,it's your money.
Also,my  ...

... .
Why beat yourself up with a large bore that you must calculate drop for when  ...

...  toy. Use WipeOut or Barns CR10 in the bore to remove all the copper, which ever  ...
...  removal of all the copper use some JB Bore Paste and Kroil, follow the  ...
... ) Run the patch back and forth in the bore 20-30 times or so, use a bore guide for  ...
... . Then run a dry patch through you bore and chamber. I was amaized at the  ...

...  anything away for the product ("Iosso Bore Cleaner") I was using. This still  ...

... , yes Weatherby only free bores it's own cartridges, all other  ...

...  everyone is aware of that so I will not bore everyone by restating the obvious. I  ...

...  was wondering what opinions are on bore guides. Are they necessary? What is the  ...

... Bore Snakes are washable so that any grit/ ...

...  six lug 7mm-08 and am intending to buy bore guide no. 18 by Possum Hollow from www. ...
...  for it fitting your rifle. There is a bore guide chart listed and it says the no.  ...
... /staticpages/pdf/Chart_PDFs/EJS_Bore_Guide_Chart.pdf Hope this helps. I  ...
...  been using a bore snake up until now. ...

...  like to hear more about the use of JB Bore paste.
I have not heard about the  ...

...  are not very accurate because of freebore should shoot mine. I do believe that  ...

...  adventurer.

His experience with a 4-bore elephant gun that his gunbearer  ...
...  and the gun went off--it was a 4-bore elephant gun, loaded twice over, and  ...

...  in a Weatherby cartridge will be free bored for safety reasons. Norma ammo is very  ...
...  ammo and without a freebore there would be some pressure issues to  ...
...  custom smiths that will minimize freebore on a Weatherby cartridges but will flat  ...

...  on. i'm pretty picky about how clean my bore is. also if it wont shoot 1/2" at 100  ...
... .
the only cleaners that go in my bore are Montana Extream and Bore-tech  ...

...  game so I'll be shopping for a big bore in the next couple of years. When I  ...

...  Browning over/under shotguns are back bored. Check the Browning website- they  ...

... , but I have started using the Otis 085 bore cleaner. Have you used that at all? I  ...

...  hunter. I will do my best to keep my bore dry but is very hard to do in Alaska  ...